ARGOX OS 214 PLUS PPLA DRIVER

Attach the edge of the ribbon on the bare core and wind it a little bit onto the core. Connecting the Power Supply Connect the power supply as below. Argox OSplus User Manual 44 pages. Serial Cabling Requirements Serial Cabling Requirements Data cables must be of fully shielded construction and fitted with metal or metalized connector shells. Please contact your supplier for assistance. Release the screw on the left bracket of the chassis.

Uploader: Shakazuru
Date Added: 6 June 2014
File Size: 35.55 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 32344
Price: Free* [*Free Regsitration Required]

argox os 214 plus ppla Connect the USB cable, Serial cable to the proper port on the printer and on your computer. Check all the data on the showing screen, if it is correct, click “Finish”. Replacing the Thermal Print Head 1. This manual will help you get to know your new printer.

Turn the wheel of the print head module to ensure the ribbon is tightly wound. Table of Contents Safety It is intended for helping you to know your printer better, then further to optimize it. Pin 9 argox os 214 plus ppla reserved for KDU keyboard device unittherefore do not connect these pins if you arglx using a general host like pplx PC.

Media Compartment Media Roll Shield It can deliver much smoother printing process and maintain top printing quality under high speed.

Argox OS Plus – Argox – Desktop Label Printers

Connecting the Power Supply Connect the power supply as below. In addition to cutting backing paper, the full-cut cutter can also work on continuous labels with adhesive. Resetting to Factory Default Settings 1. Challenger E Barcode Printer.

The “FEED” button does not make the printer cut.

OS PLUS Bartender Sürücüsü (Driver) Kurulumu

Improper firmware updating may crash printer firmware. The bare core for the ribbon must be 11 cm in length. Insert the argox os 214 plus ppla connector of the power supply into the power jack on the back of the printer.

Serial rs Interface Requirements, Parallel Interface Requirements, Serial And Parallel Ppls Requirements Serial RS Interface Requirements The required cable must have a nine-pin “D” type male connector on one end, which is plugged into the mating serial port located on the back of the printer.

Release the two screws argox os 214 plus ppla the bottom of the base housing.

Argox OS-214 Plus

Mount the extension card to J14 on the main board. If you install new bar code application software such as Bartender Ultra Lite, you should activate the seagull driver for Argox printer.

Load the media roll onto the hanger argox os 214 plus ppla left to right. Parallel Interface Requirements The required cable IEEE compliant is recommended must have a standard pin parallel connector on one end, which is plugged into the parallel port located on the back of argox os 214 plus ppla printer.

Pin assignments are as follows: Put the print head module down and press down firmly until you hear a snap. This printer has been replaced by the Argox X Note the location of the Ribbon power jack for different models in the diagrams below.

Postek G Barcode Printer. Continuous improvement of products is a ;pla of Argox Information Co. Zebra ZTdpi Barcode Printer.

Avery Dennison 64 Argox os 214 plus ppla. Unwrap the ribbon roll pack and separate the ribbon roll and the bare core. Install the extension card into the printer as follows: Replacing the Thermal Print Head 1. When the two indicators relight, release the feed button. Sato DRe Retail Printer. Remove the top cover. M4L Mobile Thermal Printer. The other end of the parallel interface cable connects to the printer connector at the host computer. I4 industrial printers are constructed with argox os 214 plus ppla all-metal frame to inherit the beauty of durability and reliability.

This manual also for: Ribbon Pick-up Holder 8. Sato TG3 Retail Printer.

Argox OS-214 plus User Manual

Loading Media The OS plus offers three different loading modes: This equipment has been argox os 214 plus ppla and found to comply with the limits for a Class A.

Put the print head module down and press down firmly until you hear a snap. Enter text from picture: The following table explains control and indicator functions.

Caring For Your Printer Caring for Your Printer Adhesives and coatings of media can over time transfer onto the printer components along the media path including the thermal print head and media sensor. By equipping with new flip-down type cutters, including full-cut and partial-cut types, I4-series Industrial printer comes with user friendly design that makes your media loading time much easier, be means of argox os 214 plus ppla media-jam free instructions.

Hold the print head module upright with one hand to allow the so to pass under it. Make sure the power switch is in the “O” position.